SleepyHead Fedora rpm package

Sleep apnea


It is not so bad getting a diagnosis for sleep apnea. Some people are not even aware of their condition. But it is important to get help, because your health could suffer. Some people might feel a little tired, but other could develop serious illnesses. For more information, see https://en.wikipedia.org/wiki/Sleep_apnea.

CPAP units


So I got this CPAP unit (almost for free because of our Nordic national health insurance). It is locked down, so I can't get any useful data directly out of it. But there is an SD card that is meant to be analyzed by my doctor. And there are free software on the Internet.

SleepyHead


Meet SleepyHead:

http://sleepyhead.jedimark.net

This is a very nice and free (GPL3) cross-platform program. Works in Windows, Mac and Linux.

It is able to import data from an SD card of the most common CPAP units. There is also support for a few pulse oximeters. Below is a screenshot of the welcome screen.


It is important to note that you use this software at your own risk. It is not official medical software and should only be for personal use. See more in the software's disclaimer in the Help menu, About.

Fedora rpm package


There is no rpm package available for Fedora, so I decided to try to build one. Install and use at your own risk. To be on the safe side, use the srpm to build your own package.


To install the software in Fedora 24, download one of the following rpm files:

Fedora 24 64-bit:
sleepyhead-1.0.0-0.3.20160703git0e04bd9.fc24.x86_64.rpm (built from git 2015-07-03 and listed as 1.0.0 Beta 2) - changed 2016-07-04

 Fedora 24 32-bit:
sleepyhead-1.0.0-0.3.20160703git0e04bd9.fc24.i686.rpm - changed 2016-07-04

Update: Moved packages to Copr, see next blog post.

Be aware that downloading random rpm packages from the Internet is not a good idea from a security point of view, so you are doing it at your own risk.


To rebuild the package, use the following file:


sleepyhead-1.0.0-0.3.20160703git0e04bd9.fc24.src.rpm - changed 2016-07-04
Update: Moved to Copr, see next blog post.

Building it requires some dependencies, mainly QT5 development libraries and build tools. The spec file has most libraries listed.

I will try to improve the spec if possible and update the packages also. Comments are welcome, I don't have experience creating many rpm packages.


These rpm packages are based on the free and open-source software SleepyHead available from http://sleepyhead.jedimark.net, developed and copyright by Mark Watkins (C) 2011-2016.

Kommentarer

Skicka en kommentar

Populära inlägg i den här bloggen

Steelseries Arctis 7 headset in Linux

Bild
UPDATE. This headset works without modifications in Linux after the changes were committed to pulseaudio in 2017.  The Steelseries Arctis series headsets are very comfortable. You can wear this headset all day long thanks to the comfortable head strap. Steelseries Arctis 7 There are three models, Arctis 3, 5 and 7. The last one is the most expensive and has wireless connection. Arctis 5 is basically the same without wireless (only USB connection). Arctis 3 has only analog inputs. I've got the Arctis 7 model and of course I'm using it with Linux. There were some issues setting it up. It works fine in Alsa, the device is recognized. You do have to adjust sound levels, at least the mic has too low sound level. Use alsamixer on command line to adjust all volume levels for the headset to 100% (the two outputs and one input). But Pulseaudio has some issues. Only the mono device (chat output) and microphone is visible. This is because the headset uses a non-supported co
Läs mer

Hard disk Firmware update on the Linux command line

Sometimes you will find that your hard disk is slow, or there are some other issues with disk performance. If you are lucky, the disk is not broken. It could have some firmware bugs, and if you are even more lucky, the manufacturer could have issued a firmware update. I've updated several hard disk firmwares in the past. Usually you have to use a boot disk with DOS or something to update the firmware. Why updating firmware? One of my hard disks in the past needed a new firmware because it was dropping out from a RAID controller. It began working fine after the firmware update. The latest hard disk that needed firmware update was Seagate 15k.7 ST3450857SS SAS. I noticed that the disks sometimes slowed down during writes and even stalled. I use two 450GB disks in software RAID 1. By googling I found that there were other people having similar problems with the same disk and that there were actually a firmware update available from Seagate. Also Dell, HP and IBM seems to ha
Läs mer

Using IBM ServeRAID M1015 card in Linux

Bild
The FusionMPT SAS2 based cards by LSI are cheap RAID cards that perform well in RAID 0 and 1 under Linux with SSDs and ZFS arrays. They are used in many 1U servers with one or two disks. They are also a popular SAS 6.0 / SATA III controllers for enthusiasts. You can get them cheap on ebay. Before SATA III was common on motherboards, this was THE card to get. It can still be useful if you need SAS disks or additional disks or have a need for disk enclosures. It is identical to the LSI MegaRAID SAS 9220-8i. The same hardware is also used in LSI 9240 and LSI 9211. It is possible to use the BIOS from another card (crossflashing) to change the features of the card. There are a few different BIOS files you can use. Specifications:  Official LSI information 8-lane, 5 GT/s PCI Express 2.0 Identical to LSI 9240-8i card 6 Gb/s per port Two x4 internal SFF-8087 connectors Controller LSISAS2008 Low cost SATA+SAS RAID solution RAID levels 0, 1, 5, 10, 50 and JBOD mode >2TB
Läs mer